View HLMP-6405-J001L_3825638.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

pdm: rev:a released status: printed: oct 18, 2002
dome packages the hlmp-6xxx series dome lamps for use as indicators use a tinted, diffused lens to provide a wide viewing angle with a high on-off contrast ratio. high brightness lamps use an untinted, nondiffused lens to provide a high luminous intensity within a narrow radiation pattern. resistor lamps the hlmp-6xxx series 5 volt subminiature lamps with built in current limiting resistors are for use in applications where space is at a premium. lead configurations all of these devices are made by encapsulating led chips on axial lead frames to form molded epoxy subminiature lamp packages. a variety of package configuration options is available. these features ? subminiature flat top package ideal for backlighting and light piping applications ? subminiature dome package diffused dome for wide viewing angle nondiffused dome for high brightness ? ttl and lsttl compatible 5 volt resistor lamps ? available in six colors ? ideal for space limited applications ? axial leads ? available with lead configurations for surface mount and through hole pc board mounting description flat top package the hlmp-pxxx series flat top lamps use an untinted, non- diffused, truncated lens to provide a wide radiation pattern that is necessary for use in backlighting applications. the flat top lamps are also ideal for use as emitters in light pipe applications. subminiature led lamps technical data hlmp-pxxx series hlmp-qxxx series hlmp-6xxx series hlmp-70xx series include special surface mount lead configurations, gull wing, yoke lead or z-bend. right angle lead bends at 2.54 mm (0.100 inch) and 5.08 mm (0.200 inch) center spacing are available for through hole mounting. for more information refer to standard smt and through hole lead bend options for subminiature led lamps data sheet. pdm: rev:a released status: printed: oct 18, 2002
2 dh as high high device standard algaas efficiency perf. emerald outline red red red orange yellow green green device description [1] drawing p005 p105 p205 p405 p305 p505 p605 untinted, nondiffused, a flat top p102 p202 p402 p302 p502 untinted, diffused, a flat top 6000 q100 6300 q400 6400 6500 q600 tinted, diffused b q105 6305 q405 6405 6505 q605 untinted, nondiffused, b high brightness q150 7000 7019 7040 tinted, diffused, low b current q155 nondiffused, low b current 6600 6700 6800 tinted, diffused, b resistor, 5 v, 10 ma 6620 6720 6820 diffused, resistor, 5 v, b 4 ma device selection guide part number: hlmp-xxxx ordering information hlmx-xxxx-x x x x x 4 x 4 prod. part number min. iv bin max. iv bin color bin selection packaging option pdm: rev:a released status: printed: oct 18, 2002
3 0.50 (0.020) ref. 0.94 1.24 (0.037) (0.049) 2.92 (0.115) max. 0.76 0.89 (0.030) (0.035) r. 0.63 0.38 (0.025) (0.015) 2.03 (0.080) 1.78 (0.070) 0.79 (0.031) 0.53 (0.021) 0.46 0.56 (0.018) (0.022) 0.25 (0.010) max. note 2 0.20 (0.008) max. cathode 1.65 1.91 (0.065) (0.075) dia. anode 11.68 10.67 (0.460) (0.420) both sides 0.18 0.23 (0.007) (0.009) 2.08 2.34 (0.082) (0.092) cathode stripe 2.21 1.96 (0.087) (0.077) (b) diffused and nondiffused figure 1. proper right angle mounting to a pc board to prevent protruding cathode tab from shorting to anode connection. package dimensions (a) flat top lamps no. anode down. yes. cathode down. cathode tab notes: 1. all dimensions are in millimetres (inches). 2. protruding support tab is connected to cathode lead. 3. lead polarity for algaas lamps is opposite to the lead polarity of subminiature lamps using other technologies. 0.46 0.56 (0.018) (0.022) 1.40 1.65 (0.055) (0.065) 0.25 (0.010) max. note 2 0.20 (0.008) max. 0.50 (0.020) ref. cathode 1.65 1.91 (0.065) (0.075) dia. anode 11.68 10.67 (0.460) (0.420) both sides 1.14 1.40 (0.045) (0.055) 0.63 0.38 (0.025) (0.015) 2.21 1.96 (0.087) (0.077) 0.18 0.23 (0.007) (0.009) 0.79 (0.031) max. 2.44 1.88 (0.096) (0.074) 2.08 2.34 (0.082) (0.092) cathode stripe pdm: rev:a released status: printed: oct 18, 2002
4 dh as high high standard algaas eff. perf. emerald parameter red red red orange yellow green green units dc forward current [1] 50 30 30 30 20 30 30 ma peak forward current [2] 1000 300 90 90 60 90 90 ma dc forward voltage 6 6 6 6 v (resistor lamps only) reverse voltage (i r = 100 m a)5 555555v transient forward current [3] 2000 500 500 500 500 500 500 ma (10 m s pulse) operating temperature range: -55 to -40 to -55 to +100 -40 to -20 to non-resistor lamps +100 +100 +100 +100 c resistor lamps -40 to +85 -20 to +85 storage temperature range c for thru hole devices 260 c for 5 seconds wave soldering temperature [1.6 mm (0.063 in.) from body] for surface mount devices: convective ir 235 c for 90 seconds vapor phase 215 c for 3 minutes absolute maximum ratings at t a = 25 c -55 to +100 notes: 1. see figure 5 for current derating vs. ambient temperature. derating is not applicable to resistor lamps. 2. refer to figure 6 showing max. tolerable peak current vs. pulse duration to establish pulsed operating conditions. 3. the transient peak current is the maximum non-recurring peak current the device can withstand without failure. do not operate these lamps at this high current. pdm: rev:a released status: printed: oct 18, 2002
5 electrical/optical characteristics, t a = 25 c standard red device hlmp- parameter symbol min. typ. max. units test conditions 6000-e00xx luminous intensity [1] i v 0.63 1.2 mcd i f = 10 ma 6000-g00xx 1.60 3.2 p005-f00xx 1.0 2.5 forward voltage v f 1.4 1.6 2.0 v i f = 10 ma all reverse breakdown v r 5.0 12.0 v i r = 100 m a voltage 6000 included angle between 2 q 1 / 2 90 deg. half intensity points [2] p005 125 peak wavelength l peak 655 nm dominant wavelength [3] l d 640 nm spectral line half width dl 1/2 24 nm all speed of response t s 15 ns capacitance c 100 pf v f = 0; f = 1 mhz thermal resistance r q j-pin 170 c/w junction-to-cathode lead luminous efficacy [4] h v 65 lm/w pdm: rev:a released status: printed: oct 18, 2002
6 device hlmp- parameter symbol min. typ. max. units test conditions p102-f00xx 1.0 20.0 p105-l00xx 10.0 30.0 p105-np000 25 80 q100-m00xx 16 45 q100-n00xx luminous intensity i v 25.0 45.0 mcd q100-pq000 40 125 q105-p00xx 40 200 q105-st000 160 500 q150-f00xx 1.0 1.8 q155-f00xx 1.0 4.0 q100 forward voltage v f 1.8 2.2 v i f = 20 ma q150/q155 1.6 1.8 i f = 1 ma all reverse breakdown v r 5.0 15.0 v i r = 100 m a voltage p105 125 q100/q150 included angle between 2 q 1 / 2 90 deg. half intensity points [2] q105/q155 28 peak wavelength l peak 645 nm measured at peak dominant wavelength [3] l d 637 nm spectral line half width dl 1/2 20 nm all speed of response t s 30 ns exponential time constant; e -t/ t capacitance c 30 pf v f = 0; f = 1 mhz thermal resistance r q j-pin 170 c/w junction-to cathode lead luminous efficacy [4] h v 80 lm/w dh as algaas red i f = 1 ma i f = 20 ma s pdm: rev:a released status: printed: oct 18, 2002
7 device hlmp- parameter symbol min. typ. max. units test conditions p202-f00xx 1.0 5.0 p205-f00xx 1.0 8.0 p205-jk000 4.0 12.5 i f = 10 ma 6300-f00xx 1.0 10.0 6300-kl000 luminous intensity [1] i v 6.3 20.0 mcd 6305-l00xx 10.0 40.0 7000-d00xx 0.4 1.0 i f = 2 ma 6600-g00xx 1.6 5.0 v f = 5.0 volts 6620-f00xx 1.0 2.0 all forward voltage v f 1.5 1.8 3.0 v i f = 10 ma (nonresistor lamps) 6600 9.6 13.0 i f ma v f = 5.0 v 6620 3.5 5.0 all reverse breakdown v r 5.0 30.0 v i r = 100 m a voltage p205 125 6305 included angle between 2 q 1 / 2 28 deg. half intensity points [2] all 90 diffused peak wavelength l peak 635 nm measured at peak dominant wavelength [3] l d 626 nm spectral line half width dl 1/2 40 nm all speed of response t s 90 ns capacitance c 11 pf v f = 0; f = 1 mhz thermal resistance r q j-pin 170 c/w junction-to-cathode lead luminous efficacy [4] h v 145 lm/w high efficiency red forward current (resistor lamps) pdm: rev:a released status: printed: oct 18, 2002
8 device hlmp- parameter symbol min. typ. max. units test conditions p402-f00xx 1.0 4.0 p405-f00xx i v 1.0 6 p405-jk000 luminous intensity 4.0 12.5 mcd i f = 10 ma q400-f00xx 1.0 8 q405-h00xx 2.5 14 forward voltage v f 1.5 1.9 3.0 v i f = 10 ma all reverse breakdown v r 5.0 30.0 v i r = 100 m a voltage p40x included angle between 125 half intensity points [2] 2 q 1 / 2 deg. q40x 90 peak wavelength l peak 600 nm dominant wavelength [3] l d 602 nm measured at peak spectral line half width dl 1/2 40 nm all speed of response t s 260 ns capacitance c 4 pf v f = 0; f = 1 mhz thermal resistance r q j-pin 170 c/w junction-to-cathode lead luminous efficacy [4] h v 380 lm/w orange pdm: rev:a released status: printed: oct 18, 2002
9 device hlmp- parameter symbol min. typ. max. units test conditions p302-f00xx 1.0 3.0 p305-f00xx 1.0 4.0 i f = 10 ma 6400-f00xx 1.0 9.0 6400-jk000 4.0 12.5 6405-j00xx luminous intensity [1] i v 3.6 20 mcd 6405-mn0xx 16 50 7019-d00xx 0.4 0.6 i f = 2 ma 6700-g00xx 1.4 5.0 v f = 5.0 volts 6720-f00xx 0.9 2.0 all forward voltage v f 2.0 2.4 v i f = 10 ma (nonresistor lamps) 6700 9.6 13.0 forward current i f ma v f = 5.0 v 6720 (resistor lamps) 3.5 5.0 all reverse breakdown v r 5.0 50.0 v voltage p305 125 6405 included angle between 2 q 1 / 2 28 deg. half intensity points [2] all 90 diffused peak wavelength l peak 583 nm measured at peak dominant wavelength [3] l d 585 nm spectral line half width dl 1/2 36 nm all speed of response t s 90 ns capacitance c 15 pf v f = 0; f = 1 mhz thermal resistance r q j-pin 170 c/w junction-to-cathode lead luminous efficacy [4] h v 500 lm/w yellow pdm: rev:a released status: printed: oct 18, 2002
10 high performance green device hlmp- parameter symbol min. typ. max. units test conditions p502-f00xx 1.0 3.0 p505-g00xx 1.6 6.3 6500-f00xx 1.0 7.0 i f = 10 ma 6505-l00xx 10.0 40.0 7040-d00xx luminous intensity [1] i v 0.4 0.6 mcd i f = 2 ma 6800-g00xx 1.6 5.0 v f = 5.0 volts 6820-f00xx 1.0 2.0 all forward voltage v f 2.1 2.7 v i f = 10 ma (nonresistor lamps) 6800 9.6 13.0 forward current i f ma v f = 5.0 v 6820 (resistor lamps) 3.5 5.0 all reverse breakdown v r 5.0 50.0 v i r = 100 m a voltage p505 125 6505 included angle between 2 q 1 / 2 28 deg. half intensity points [2] all 90 diffused peak wavelength l peak 565 nm dominant wavelength [3] l d 569 nm spectral line half width dl 1/2 28 nm all speed of response t s 500 ns capacitance c 18 pf v f = 0; f = 1 mhz thermal resistance r q j-pin 170 c/w junction-to-cathode lead luminous efficacy [4] h v 595 lm/w notes: 1. the luminous intensity for arrays is tested to assure a 2.1 to 1.0 matching between elements. the average luminous intensity for an array determines its light output category bin. arrays are binned for luminous intensity to allow i v matching between arrays. 2. q 1 / 2 is the off-axis angle where the luminous intensity is half the on-axis value. 3. dominant wavelength, l d , is derived from the cie chromaticity diagram and represents the single wavelength that defines the color of the device. 4. radiant intensity, i e , in watts/steradian, may be calculated from the equation i e =i v / h v , where i v is the luminous intensity in candelas and h v is the luminous efficacy in lumens/watt. pdm: rev:a released status: printed: oct 18, 2002
11 device hlmp- parameter symbol min. typ. max. units test conditions p605-f00xx luminous intensity i v 1.0 1.5 mcd i f = 10 ma q600-f00xx 1.0 1.5 q605-f00xx 1.0 7.5 forward voltage v f 2.2 3.0 v i f = 10 ma all reverse breakdown v r 5.0 v i r = 100 m a voltage p605 included angle between 125 half intensity points [2] 2 q 1 / 2 deg. q60x 90 peak wavelength l peak 558 nm dominant wavelength [3] l d 560 nm measured at peak spectral line half width dl 1/2 24 nm p605/ q600 speed of response t s 3100 ns capacitance c 35 pf v f = 0; f = 1 mhz thermal resistance r q j-pin 170 c/w junction-to-cathode lead luminous efficacy [4] h v 656 lm/w emerald green [1] note: 1. please refer to application note 1061 for information comparing standard green and emerald green light ouptut degradation. pdm: rev:a released status: printed: oct 18, 2002
12 standard red, dh as algaas red standard red and dh as algaas red high efficiency red, orange, yellow, high performance green, and emerald green her, orange, yellow, and high performance green, and emerald green low current figure 1. relative intensity vs. wavelength. figure 2. forward current vs. forward voltage. (non-resistor lamp) figure 3. relative luminous intensity vs. forward current. (non-resistor lamp) forward current ?ma 100 0 forward voltage ?v 80 60 50 70 20 0 10 30 40 0.5 1 1.5 2 2.5 3 3.5 90 high performance green, emerald green yellow high efficiency red/orange pdm: rev:a released status: printed: oct 18, 2002
13 figure 4. relative efficiency (luminous intensity per unit current) vs. peak current (non-resistor lamps). figure 5. maximum forward dc current vs. ambient temperature. derating based on t j max = 110 c (non-resistor lamps). figure 6. maximum tolerable peak current vs. pulse duration. (i dc max as per max ratings) (non-resistor lamps). standard red dh as algaas red standard red her, orange, yellow, and high performance green dh as algaas red her, orange, yellow, and high performance green, and emerald green pdm: rev:a released status: printed: oct 18, 2002
14 figure 9. relative intensity vs. angular displacement. figure 7. resistor lamp forward current vs. forward voltage. figure 8. resistor lamp luminous intensity vs. forward voltage. 14 pdm: rev:a released status: printed: oct 18, 2002
15 hlmx-xxxx-x x x x x 4 x 4 prod. part number min. iv bin max. iv bin color bin selection packaging option ordering information intensity bin limits bin min. max. a 0.10 0.20 b 0.16 0.32 c 0.25 0.50 d 0.40 0.80 e 0.63 1.25 f 1.00 2.00 g 1.60 3.20 h 2.50 5.00 j 4.00 8.00 k 6.30 12.50 l 10.00 20.00 m 16.00 32.00 n 25.00 50.00 p 40.00 80.00 q 63.00 125.00 r 100.00 200.00 s 160.00 320.00 t 250.00 500.00 u 400.00 800.00 v 630.00 1250.00 w 1000.00 2000.00 x 1600.00 3200.00 y 2500.00 5000.00 color bin limits package bin min. max. emerald green 0 full distribution 9 552 556 8 555 559 7 558 562 6 561 565 green 0 full distribution 6 561 565 5 564 568 4 567 571 3 570 574 2 573 577 yellow 0 full distribution 1 581.5 585.0 3 584.0 587.5 2 586.5 590.0 4 589.0 592.5 5 591.5 593.5 6 591.5 595.0 7 594.0 597.5 orange 0 full distribution 1 596.5 600.0 2 599.0 602.5 3 601.5 604.0 4 603.8 608.2 5 606.8 611.2 6 609.8 614.2 7 612.8 617.2 8 615.8 620.2 pdm: rev:a released status: printed: oct 18, 2002
mechanical option 00 straight leads, bulk packaging, quantity of 500 parts 10 right angle housing, bulk packaging, quantity of 500 parts 11 gull wing leads, 12 mm tape on 7 in. dia. reel, 1500 parts per reel 12 gull wing lead, bulk packaging, quantity of 500 parts 14 gull wing leads, 12 mm tape on 13 in. dia. reel, 6000 parts per reel 21 yoke leads, 12 mm tape on 7 in. dia. reel, 1500 parts per reel 22 yoke leads, bulk packaging, quantity of 500 parts 24 yoke leads, 12 mm tape on 13 in. dia. reel, 6000 parts per reel 31 z-bend leads, 12 mm tape on 7 in. dia. reel, 1500 parts per reel 32 z-bend leads, bulk packaging, quantity of 500 parts 34 z-bend leads, 12 mm tape on 13 in. dia. reel, 6000 parts per reel 1l 2.54 mm (0.100 inch) center lead spacing, long leads; 10.4 mm (0.410 in.) 1s 2.54 mm (0.100 inch) center lead spacing, short leads; 3.7 mm (0.145 in.) 2l 5.08 mm (0.200 inch) center lead spacing, long leads; 10.4 mm (0.410 in.) 2s 5.08 mm (0.200 inch) center lead spacing, short leads; 3.7 mm (0.145 in.) note: all categories are established for classification of products. products may not be available in all categories. please contact your local agilent representative for further clarification/information. www.agilent.com/semiconductors for product information and a complete list of distributors, please go to our web site. for technical assistance call: americas/canada: +1 (800) 235-0312 or (408) 654-8675 europe: +49 (0) 6441 92460 china: 10800 650 0017 hong kong: (+65) 6271 2451 india, australia, new zealand: (+65) 6271 2394 japan: (+81 3) 3335-8152(domestic/interna- tional), or 0120-61-1280(domestic only) korea: (+65) 6271 2194 malaysia, singapore: (+65) 6271 2054 taiwan: (+65) 6271 2654 data subject to change. copyright ? 2002 agilent technologies, inc. obsoletes 5988-4077en april 30, 2002 5988-6260en pdm: rev:a released status: printed: oct 18, 2002

▲Up To Search▲

Price & Availability of HLMP-6405-J001L

	To Download HLMP-6405-J001L Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .